Undercover Systems – Decking Pros NW

1. What is an underdeck or undercover system?Undercover systems INC

An Under Deck System, sometimes referred to as an Under Deck Ceiling, is similar to a dropped ceiling beneath your second-story deck and is made of wood. Actually, the rainwater that would ordinarily fall between the deck boards is collected by the roof and channeled into a rain gutter, away from your deck.Deck building

In many ways, it is comparable to the construction that we all see above the Gas Pumps at a gas station or your outdoor living room. There is no pitched roof, but instead, a collection system made of designed metal panels that is attached to a frame structure. Raised decks already have a framework that is comparable to this. A simple collection system is used, with the water being channeled into a gutter. Drainage is accomplished through the use of a gutter and downspout, which channel the rainwater into a regulated place.Outdoor kitchen construction

Simply described, it is a waterproof ceiling that is installed underneath your deck by taking advantage of a useable outdoor living space.

2. The advantages of undercover systems

a. You can custom your under systems

There is a variety of patented system designed for your family outdoor living space. Below is some idea for you:

Stone undersystems deckUnder deck ceilingsElectrical access light underdeck systemUnderside wood ceilingsUndercover system living room with aluminium

b. Take advantage of the underside of your deck

Besides from the undercover systems, you can add more function rather than a living roomUndercover hot tubUnder deck fire pitUndercover railing installation

c. Providing dry protection in the greater Seattle area

Snap-together vinyl ceiling panels gather and drain water away from your new dry room, and they are easy to assemble. You may use it to cover the unattractive underbelly of your deck, transforming it into a clean, bright, and dry outdoor living place. It is completely maintenance-free.Dry outdoor quality living

d. Easy maintenance

Cleaning the under deck ceiling is usually a short sweep. Brush away cobwebs, filth, and dust from your ceiling using an upside-down broom. If your ceiling starts to look dirty, just clean the panels with a stain remover and degreaser-like dish soap. Power washing the upper deck or the metal panels won’t hurt them either. Using a typical power washer with a pressure of 1300-3000 PSI should not cause any issues. With pressure washers over 3000 PSI, a little amount of water can escape through the drainage system.

e. Added property value with a quality deck designStunning undercover systems

A deck ceiling can add thousands to your home’s worth. Using this method, you can convert the underutilized area under your deck into dry storage or extra outdoor living space that potential buyers will adore. Your new outdoor living area can incorporate built-in cooking and dining places. You can build a hot tub room or storage. With ceiling fans and heaters, your outdoor area may be used all year round. Using it in any way adds important usable square footage to your property with exclusive provider.

3. Undersystems installation process

a. Purlin construction under the existing deck

Layout the 2×4 purlins 3 feet apart, parallel to the building’s façade. The panels should slope toward the outside border of the deck by about 1/4 in. per foot to allow water to drain away from the balcony. A good rule of thumb is that the purlin at the deck’s outer end should be 3 inches lower than the purlin along the house’s side for 12 feet.

Start by joist-marking every purlin point on the deck. Afterward, attach the exterior purlin to the house. Stitch a cord between them. At each of the other purlin sites, measure the deck joists to the string below them. The spacer block widths are determined by subtracting the purlin thickness from the above specifications. Make sure it is a washable mold resistant surface so you can clean it later, for better customer satisfaction.

b. Attach the panels into the purlin systemPanel under deck roof

Attach the first panel to the purlin with the roofing screws, starting at one end and working your way out. Every other valley should have a screw in it. Squeeze the screws together just enough to compress the washer a little.

Underdeck systems are created by overlapping the next panel onto the one you just put and attaching it the same way as the previous panel. You may find that the last meeting is excessively long when you end. You can overlap it a little more or cut it to match your needs. It is simple to cut panels to the desired length or breadth with a circular saw and a carbide blade.

You can pick different materials; aluminum panels are good to choose for your new deck. They complement your patio and create a shiny and polished look. Vinyl panels are another option for your under deck ceiling.

c. Installing a gutter systemGutter system installation

Depending on how your deck is constructed, you may have to get creative in order to come up with an attachment method that works. In order to accommodate the fact that the in-stock 12-foot panels did not quite reach the beams on the deck, vertical were fastened to every other joist to serve as attachment points for the gutters. Then he fastened the gutter hangers to the 2x4s with a drywall screw. Drainage should be provided by sloping the gutters toward the downspout.

Finished product

Leave a Reply

Your email address will not be published.